并有逐步取代传统絮凝剂的趋势。西欧各国于1976年开始生产聚合氯化铝，用作工业污水处理絮凝剂;美国、加拿大已于1983年批准将其用于城市给水和工业污水处理。 聚合氯化铝是水处理混凝剂的常用药剂，水处理效果显著，在饮用水、工业污水净化中有着至关重要的作用。我们常用到的聚合氯化铝含量有：26%、28%、30%。聚合氯化铝含



量的不同，用途也不同，相对应的聚合氯化铝价格也不同
水污染的危害显而易见聚合氯化铝合理攻坚管理水污染.
家对854个乡镇进行调查,每天的排放量达36个处理一吨沙的成本多少啊 高了承受不了啊 没有利润了 
在这了河南安家净环保技术人员通过多年的现场测试 总结出来的使用量和使用成本给大家解读一下 
1kg聚丙烯酰胺可以溶1吨是pam溶液 一吨聚丙烯酰胺的价格在8000-12000元之间 咱就按照1万元来计算 1吨聚丙烯酰胺溶液的药剂成本是10块钱 那么处理一吨污水的需要多少聚丙烯酰胺AM聚丙烯酰胺的合成及工艺物理特性：PAM由丙烯腈与水在骨架铜催化剂作用下直接反响生成聚丙烯酰胺再经离子交流聚合单调，等工序即得废品，工艺简介如下：催化剂：催化水合CH2=CHCN+H2O 湿度 CH2=CHCONH2 聚合nCH2=CHCONH2-引发剂-CH2CHCONH2

    聚丙烯酰胺工业用处：聚丙烯酸胺(PAM)分子量高、水溶性好、可调理分子量，并能够引进各种离子基团以得到特定的性能。低分子量是分散资料有效增调剂或稳定剂，高分子量是重要的絮凝剂，它能够制造出亲水而水不溶性的凝胶，它对许多团体外表和溶解物质有良可以作为净水药剂使用，也可以在造纸领域被当做助留剂使用，部分造纸使用草浆纤维较短，细胞杂质较高，导致了纸张强度较差，抄纸过程中滤水困难。对于此问题处理办法有两种：机械截留和胶体絮凝。

机械截留类似于过滤作用，它适用于纸张中较长部分纤维，纤细组分隐藏高的原因无法由此说明，助留剂的助留作用也无法用此解释；

胶体絮凝作用为：凝聚作用和絮凝作用。分子量较小或者无机盐、电荷密度较高的聚合物使胶体悬浮液稳定性丧失从而发生絮聚作用称之为凝聚作用，经过电荷中和、异相凝聚和补缀作用几种方法产生的沉积物。聚合氯化铝是指聚凝作用中所提到的无机盐。电荷密度较高的聚合物。

运用聚合氯化铝处理了造纸进程由酸性改为中、碱性规模，纸浆中的阴离子杂质的问题，纸机操作以及纸质量的一系列问题，聚合氯化铝带有阳电荷，可以有效的控制阴离子的作用，有利于纸张滤水性 改善，聚合氯化铝极容易在纤维外表形成吸附，还可以将带有负电荷的填料和纤维吸附，使细料的藏着率有效的提高，浆料的滤水功效得到进一步的改善好的粘附力。由于以上性能PAM普遍应用于絮凝、增稠、减阻、拟胶、粘结、阻垢等范畴 。

    阴离子聚丙烯酰胺依据不同用处和用户对产品性能的央求，可选用不同分子量运用。

    在工业废水处置中，特别是关于悬浮颗粒、较粗、浓度高、粒子带阳电荷，水的PH值为中性工碱性的污水如钢铁厂废水，电镀厂废水，冶金废水，洗煤废水等污水处置效果很好。

    在饮用水处置。我国很多自来水厂的水源自江河泥少及矿物质含量高，比拟混浊，虽经过沉淀处置，但仍达不到央求，需求投加絮凝剂，才干使水质变清，很多自来水厂采用无机絮凝剂，但投加量大，构成污泥量增大效果不好，采用阴离子聚丙烯酰胺作絮凝剂，投加量是无机絮凝的50分之一但效果是无机絮凝剂的几倍至几十倍，特别是我公司消费的聚丙烯酰胺，剩余单体已抵达食品级(小于0.05%)，接近国外先进程度，对处置饮用水更为合适，关于有机物污染严重的江河水和阴离子聚丙烯酰胺配合运用效果更好。

    聚丙烯酰胺用作淀粉厂及酒精厂的流失淀粉及酒糟的回收。往常很多淀粉厂排出的废水内淀粉很高，排放之后影响环境，糜费资源，投加PAM，使淀粉沉淀，沉淀物经压滤机压滤变成饼类可作饲料，酒精厂大量的酒糟就是采用这种工艺加工的，黑龙江某酒精厂就是聚丙烯酰胺作絮凝剂，对酒糟中止回收的而且获得了很大的经济效益。

    聚丙烯酰胺用作油田调剖堵水的堵水剂，三次采油的驱油剂。

    聚丙烯酰胺用作造纸助剂，PAM在造纸方面用处很普遍，可作为长纤维造纸分散剂，干湿加强剂，助留，助滤剂及造纸废水的絮凝剂等。

    最新型的水处置剂聚丙烯酰胺，在很多场所处置污水和上水时，阴离子聚丙烯酰胺和阳离子聚丙烯酰胺配合运用要比单独运用一种离子型聚丙烯酰胺产生十分显著和协同效应，PAM对降低外表张力的才干要远远大于同条件下阳离子或阴离子单独存在的才干，为抵达降低外表张力的央求，需求同时运用阴离子和阳离子聚丙烯酰胺，便两者如运用不当，会产生白色沉淀物，失去运用效果 。而PAM具有两性离子的特性，它能够完成阴离子、阳离子的配合协同作用，面没有任何沉淀物的产生，特别是对水质状况比拟复杂或水的性质经常变化的，运用PAM作为处置絮凝剂更为便当，效果更好。

    在污水预处置中采用的污泥取自以钱塘江水为水源的沉淀池，该水厂以聚合氯化铝PAC为絮凝剂。污泥经自然浓缩到含固率为2.7%～2.8%，经测定，污泥中有机物含量为12.1%，sj如含量为52.1%，Al。含量为20.2%。 PAM有阳离子型、阴离子型和非离子型三品种型。非离子型PAM溶解速度较慢，普通不用于污泥预处置，因而实验仅选用两种有代表性的阳离子聚丙烯酰胺和阴离子聚丙烯酰胺。阳离子型PAM分子量1200万，丙烯酰胺单体含量0.012%。阴离子型PAM分子量1250万，丙烯酰胺单体含量0.013％。两种PAM配制浓度均为0.05％%，冰箱冷藏24h后运用。

    (1)PAM预处置污泥取lOOml污泥，放入300ml的烧杯中，采用六联搅拌机以1130rpm的转速快 速搅拌30s后疾速投加～定量制备好的PAM，继续以lOOrpm的转速搅拌30s， 然后降低搅拌机转速到20～30rpm慢速搅拌60s促进絮凝。分别测定预处置后污泥的比阻、毛细吸水时间(CST)、过滤液的粘度和离心液的粘度。

    (2)比阻按考克力(Coackley)提出的实验办法，采用布氏漏斗实验。布氏漏斗的直径为80mm，滤纸采用由70mm定量中速滤纸，实验真空度控制为0.01MPa。实验反复3次取均匀值。

    (3)为了降低比阻，进步污泥脱水效果，在污泥脱水前普通均需对污泥中止预处置。污泥预处置的办法有冰冻一冻结预处置、热处置、酸处置、碱处置、石灰预处置和高分子絮凝剂预处置等，其中高分子絮凝剂聚丙烯酰胺(PAM) 预处置是目前国内外采用最普遍的预处置办法。
投加率的合理肯定对降低污泥预处置费用相当关键。对选择聚丙烯酰胺的实验办法的研讨已展开多年，包括比阻、CST值、污泥流变性、分别液粘度、活动电流等。The synthesis and process physical properties of AM polyacrylamide: PAM is prepared by direct reaction of acrylonitrile with water under the action of framework copper catalyst, and then dried by ion exchange polymerization. The process is as follows: catalyst: catalytic hydration CH2 = CHCN + H2 humidity CH2 = CHCONH2 polymerization nCH2 = CHCONH2 - initiator - CH2CHCONH2
Industrial uses of polyacrylamide: Polyacrylamide (PAM) has high molecular weight, good water solubility, adjustable molecular weight, and can introduce various ionic groups to obtain specific properties. Low molecular weight is an effective additive or stabilizer for dispersing materials. High molecular weight is an important flocculant. It can produce hydrophilic and water-insoluble gel, which has good adhesion to many groups of surface and dissolved substances. Because of the above properties, PAM is widely used in flocculation, thickening, drag reduction, glue imitation, bonding, scale inhibition and other fields.
Anionic polyacrylamide can be used in different molecular weights according to different uses and user's requirements for product performance.
In industrial wastewater treatment, especially for suspended particles, coarser, high concentration, positive charged particles, neutral and alkaline wastewater such as iron and steel plant wastewater, electroplating plant wastewater, metallurgical wastewater, coal washing wastewater and other wastewater treatment effect is very good.
In drinking water treatment. The water source of many Waterworks in our country is low in mud and high in mineral content, which is turbid. Although it has been treated by precipitation, it still can not meet the requirements. Flocculants are needed to make the water quality clear. Many waterworks use inorganic flocculants, but the amount of inorganic flocculants is large, resulting in poor effect of sludge increase. Anionic polyacrylamide  acrylamide monomer was 0.012%. The molecular weight of anionic PAM was 12.5 million and the content of acrylamide monomer was 0.013%. The concentration of two kinds of PAM is 0.05%. They are used after refrigeration for 24 hours.
(1) PAM pretreatment sludge takes lOml sludge and puts it into a 300 ml beaker. Six-unit mixers are used to mix at 1130 RPM speed for 30 seconds, and then the PAM is added to the sludge quickly and quantitatively. The PAM is stirred at lOOrpm speed for 30 seconds, then the speed of the mixer is reduced to 20-30 rpm and the slow stirring speed is 60 seconds to promote flocculation. The specific resistance of pretreated sludge, capillary water absorption time (CST), the viscosity of filtrate and the viscosity of centrifuge were measured.
(2) The specific resistance is tested by Brinell funnel according to the test method proposed by Coackley. The diameter of Brinell funnel is 80 mm. The filter paper is made of 70 mm medium speed filter paper. The vacuum degree of the test is controlled to 0.01 MPa. The experiment was repeated three times to get the average value.
(3) In order to reduce specific resistance and improve sludge dewatering effect, sludge should be pretreated before sludge dewatering. Sludge pretreatment methods include freeze-thaw pretreatment, heat treatment, acid treatment, alkali treatment, lime pretreatment and polymer flocculant pretreatment. Polymer flocculant polyacrylamide (PAM) pretreatment is the most widely used pretreatment method at home and abroad.

    (5)实验研讨标明：投加阳离子型和阴离子型PAM后污泥比阻都降低近2个数量级，显著改善了污泥的脱水性能。阴离子加率为0.3kg/T干污泥，阳离子聚丙烯酰胺絮率为1.5kg/T于污泥，可见阴离子型PAM的投加率远小于阳离子型PAM的投加率，且阴离子型PAM的价钱约是阳离子型PAM价钱的1/2，故阴离子型PAM可作为自来水厂污泥预处置药剂的首选。

    (6)依据CST值变化肯定PAM最投加率与测定比阻得到的最投加率分歧。并且CST值与比阻之间存在线性相关关系，比阻值越大，CST值越大，因而能够采用CST值来近似替代污泥比阻反映污泥的脱水性能。与比阻相比，cST值测定快速、烦琐，不但适用于实验室研讨，还可用于消费现场，快速理解污泥脱水性能的变化，使操作人员及时调楚PAM投加率，俭省药剂费。is used as flocculant, and the dosage is inorganic flocculant. One fiftieth of the flocculants, but the effect is several times to dozens of times that of inorganic flocculants. Especially the polyacrylamide produced by our company, the residual monomers have reached the food grade (less than 0.05%), close to the advanced level abroad, non-toxic, more suitable for the treatment of drinking water, and better for the use of organic pollutants polluted river water and anionic polyacrylamide.
Polyacrylamide is used to recover lost starch and distiller's grains in starch and alcohol factories. At present, the starch in the waste water discharged by many starch factories is very high. After discharging, it affects the environment, wastes resources, and adds PAM to make starch precipitate. The precipitate is filtered by pressure filter to become cake and can be used as feed. A large number of distillers'grains in the alcohol factories are processed by this process. A certain alcohol factory in Heilongjiang Province uses polyacrylamide as flocculant, which recycles the distillers' grains and obtains a great deal of experience. Economic benefits.
Polyacrylamide is used as water shutoff agent for profile control and water shutoff in Oilfield and oil displacement agent for tertiary oil recovery.
Polyacrylamide is used as paper-making additive. PAM is widely used in paper-making. It can be used as long fiber paper-making dispersant, wet and dry reinforcing agent, retention aid, filter aid and flocculant of paper-making wastewater.
The latest type of water treatment agent polyacrylamide, when treating sewage and water in many occasions, the combination of anionic polyacrylamide and cationic polyacrylamide has a very significant and synergistic effect than using one kind of ionic polyacrylamide alone. The ability of PAM to reduce surface tension is much greater than the ability of cations or anions existing alone under the same conditions. For the requirement of low surface tension, both anionic and cationic polyacrylamide need to be used at the same time. If they are used improperly, white precipitates will be produced and the effect of using them will be lost. PAM has the characteristics of amphoteric ions. It can complete the coordination of anions and cations. There is no precipitate on the surface. Especially, it is more convenient to use PAM as a flocculant because of the complex water quality or the changeable nature of water.
The sludge used in sewage pretreatment is taken from the sedimentation tank with Qiantang River water as its source of water, and PAC is used as a flocculant in the water plant. The sludge was naturally concentrated to a solid content of 2.7%-2.8%. The organic matter content in the sludge was 12.1%, SJ content was 52.1%, Al content was determined. The content was 20.2%. There are three types of PAM: cationic, anionic and nonionic. Non-ionic PAM dissolves slowly and is generally not used for sludge pretreatment. Therefore, only two representative cationic polyacrylamides and anionic polyacrylamides are selected in the experiment. The molecular weight of cationic PAM was 12 million and the content of

    (7)不管是阳离子聚丙烯酰胺絮凝剂还是阴离子聚丙烯酰胺絮凝剂，随着，滤液和离心液粘度都呈现与比阻和CST值类似的变化规律，呈现了明显的最小值，而且该最小值对应投加率与污泥比阻和CST值实验得到的分歧。该办法断定而且还有可能用作消费上在线控制PAint最 佳投加率的参数，但其在消费上的应用还需做进一步的实验研讨。
阴离子溶液呢 根据多次实验和各个厂家的基本情况 总结一下 每吨污水需要溶液在少则2-3kg  多则3-5kg 这样算来 处理一吨沙子只要是设备合适不浪费 处理成本都在1元一下 低至0.3-0.5元 如果沙场选择自然沉淀 不用压滤机减少成本的话 一吨污水处理成本在0.1元左右 所以各位老板 这个成本价格是可以接受的 
欢迎各个洗沙场老板来电咨询 我们河南安家净环保聚丙烯酰胺提高免费试用 寄样服务 联系电话 15838356978  18838138890  Cost calculation of sewage treatment
Polyacrylamide anion is a necessary agent for pressure filtration and dehydration in the sand washing field of a sewage plant. The cost of PAM is the first consideration of many sand owners, including the use of sedimentation speed circulating water. It is known that the cost of producing a ton of sand is the one in the sand field. The larger the output is, the better the daily profit can be guaranteed Many sand market customers call to ask us how much the cost of handling a ton of sand is too high to bear. There is no profit
In this paper, Henan anjiajing environmental protection technical personnel summed up the
5.3亿吨.其间工业废水达成协议5.5亿吨. 这些废水绝大部分未经处理就直接排放, 污染了江河湖海. 水污染的危害是不是显而易见的.水体污染,水质恶化对人体健康和人类日子,出产都带来了严重的危害. Over the years, polyaluminium chloride has developed into a flocculant with mature technology and large market sales, and has gradually replaced the traditional flocculant. Western European countries began to produce polyaluminium chloride as flocculant for industrial sewage treatment in 1976, and the United States and Canada approved its use in urban water supply and industrial sewage treatment in 1983. Polyaluminium chloride (PAC) is a commonly used coagulant in water treatment. Its water treatment effect is remarkable, and it plays an important role in drinking water and industrial sewage purification. The content of polyaluminium chloride is 26%, 28% and 30%. The content of polyaluminium chloride is different, the use is different, and the corresponding price of polyaluminium chloride is also differ