北京恒正同创科技有限公司，博科Brocade光纤交换机金牌代理商，我们希望不仅为广大用户
提供优质的产品，更能在产品售后服务上令您满意，免除您的后顾之忧。产品动态详情请登录公司官网：www.brocader.com.cn

Brocade和Cisco光纤交换机级联配置

1.配置异构交换机平台协同工作模式

Cisco 9120配置过程

激活前8个端口
switch# config t
Enter configuration commands, one per line.  End with CNTL/Z.
switch(config)#interface fc1/1-8
switch(config-if)# no shutdown switch(config-if)# end
配置交换机协同工作模式
switch# config t
Enter configuration commands, one per line.  End with CNTL/Z.
switch(config)# vsan database
switch(config-vsan-db)# vsan 1 interop
switch(config-vsan-db)# end

配置domain ID
switch# config t
Enter configuration commands, one per line.  End with CNTL/Z.
switch(config)# fcdomain domain 100 preferred vsan 1
switch(config)# end

激活VSAN
switch# config t
Enter configuration commands, one per line.  End with CNTL/Z.
switch(config)# vsan database
switch(config-vsan-db)# vsan 1 suspend
switch(config-vsan-db)# no vsan 1 suspend
switch(config-vsan-db)# end

察看修改之后的系统配置信息
switch# show running
version 2.0(2b)
vsan database
  vsan 1 interop 1
fcdomain domain 100 preferred vsan 1
fcdomain fcid persistent vsan 1
boot kickstart bootflash:/m9100-s1ek9-kickstart-mz.2.0.2b.bin
boot system bootflash:/m9100-s1ek9-mz.2.0.2b.bin
kernel core target 0.0.0.0
kernel core limit 1

snmp-server user admin network-admin auth md5 0xeec64ba2afbe9b65e13b23882ac6ae05
 priv 0xeec64ba2afbe9b65e13b23882ac6ae05 localizedkey
username admin password 5 $1$V3smTQpb$MTvub69DkVBxdCt9BsEDB1  role network-admin
callhome
  switch-priority 7
snmp-server enable traps license
interface mgmt0
  ip address 192.168.70.139 255.255.255.0

interface fc1/1
  no shutdown

interface fc1/2
  no shutdown

interface fc1/3
  no shutdown

interface fc1/4
  no shutdown

interface fc1/5
  no shutdown

interface fc1/6
  no shutdown

interface fc1/7
  no shutdown

interface fc1/8
  no shutdown

interface fc1/9
interface fc1/10
interface fc1/11
interface fc1/12
interface fc1/13
interface fc1/14
interface fc1/15
interface fc1/16
interface fc1/17
interface fc1/18
interface fc1/19
interface fc1/20
switch#

察看端口连接状态信息
switch# show interface brief

-------------------------------------------------------------------------------
Interface  Vsan   Admin  Admin   Status          FCOT   Oper  Oper   Port
                  Mode   Trunk                          Mode  Speed  Channel
                         Mode                                 (Gbps)
-------------------------------------------------------------------------------
fc1/1      1      auto   on      up               swl    F       2    --
fc1/2      1      auto   on      up               swl    F       2    --
fc1/3      1      auto   on      up               swl    E       2    --
fc1/4      1      auto   on      notConnected     swl    --           --
fc1/5      1      FX     --      notConnected     swl    --           --
fc1/6      1      FX     --      notConnected     swl    --           --
fc1/7      1      FX     --      notConnected     swl    --           --
fc1/8      1      FX     --      notConnected     swl    --           --
fc1/9      1      FX     --      sfpAbsent        --     --           --
fc1/10     1      FX     --      sfpAbsent        --     --           --
fc1/11     1      FX     --      sfpAbsent        --     --           --
fc1/12     1      FX     --      sfpAbsent        --     --           --
fc1/13     1      FX     --      sfpAbsent        --     --           --
fc1/14     1      FX     --      sfpAbsent        --     --           --
fc1/15     1      FX     --      sfpAbsent        --     --           --
fc1/16     1      FX     --      sfpAbsent        --     --           --
fc1/18     1      FX     --      sfpAbsent        --     --           --
fc1/19     1      FX     --      sfpAbsent        --     --           --
fc1/20     1      FX     --      sfpAbsent        --     --           --

刀片中心光纤交换机模块配置

禁止交换机
brocadessm:USERID> switchdisable

修改Domain ID
brocadessm:USERID> configure

Configure...

  Fabric parameters (yes, y, no, n): [no] yes

    Domain: (1..239) [1] 99
    R_A_TOV: (4000..120000) [10000]
    E_D_TOV: (1000..5000) [2000]
    WAN_TOV: (0..30000) [0]
    MAX_HOPS: (7..19) [7]
    Data field size: (256..2112) [2112]
    Sequence Level Switching: (0..1) [0]
    Disable Device Probing: (0..1) [0]
    Suppress Class F Traffic: (0..1) [0]
    Switch PID Format: (1..2) [1]
    Per-frame Route Priority: (0..1) [0]
    Long Distance Fabric: (0..1) [0]
    BB credit: (1..27) [16]

  Insistent Domain ID Mode (yes, y, no, n): [no]
  Virtual Channel parameters (yes, y, no, n): [no]
  Zoning Operation parameters (yes, y, no, n): [no]
  RSCN Transmission Mode (yes, y, no, n): [no]
  Arbitrated Loop parameters (yes, y, no, n): [no]
  System services (yes, y, no, n): [no]
  Portlog events enable (yes, y, no, n): [no]
  ssl attributes (yes, y, no, n): [no]
  http attributes (yes, y, no, n): [no]
  snmp attributes (yes, y, no, n): [no]
  rpcd attributes (yes, y, no, n): [no]
  cfgload attributes (yes, y, no, n): [no]
  webtools attributes (yes, y, no, n): [no]
WARNING: The domain ID will be changed. The port level zoning may be affected

brocadessm:USERID> msPlMgmtDeactivate
Switch is in Offline state.

修改协同工作模式
brocadessm:USERID> interoper mode 1
The switch effective configuration will be lost when the operating mode is changed; do you want to continue? (yes, y, no, n): [no] y
Interopmode is enabled

Note: It is recommended that you reboot this switch for the new change to take effect.

重新引导交换机
brocadessm:USERID> fastboot
 Broadcast message from root (pts/0) Tue Jun 13 10:07:45 2006... The system is going down for reboot NOW !! USERID
Password:
Please change your passwords now.
Use Control-C to exit or press 'Enter' key to proceed.
Password was not changed. Will prompt again at next login
until password is changed.
brocadessm:USERID>

激活交换机
brocadessm:USERID> switchenable

察看修改配置之后的交换机状态

brocadessm:USERID> switchshow
switchName: brocadessm
switchType: 22.0
switchState: Online  
switchMode: Interop
switchRole: Principal
switchDomain: 99
switchId: fffc63
switchWwn: 10:00:00:05:1e:02:78:c6
zoning:         OFF
switchBeacon: OFF

Area Port Media Speed State
==============================
  0   0   id    2G   No_Light 
  1   1   cu    2G   Online    F-Port  21:00:00:14:5e:24:a9:04
  2   2   cu    2G   Online    F-Port  21:00:00:14:5e:24:a9:36
  3   3   cu    2G   Online    F-Port  21:00:00:14:5e:24:a9:7a
  4   4   cu    2G   Online    F-Port  21:00:00:14:5e:24:a9:b6
  5   5   cu    2G   Online    F-Port  21:00:00:14:5e:24:a9:28
  6   6   cu    2G   Online    F-Port  21:00:00:14:5e:24:aa:f6
  7   7   cu    2G   Online    F-Port  21:00:00:14:5e:24:aa:f0
  8   8   cu    2G   Online    F-Port  21:00:00:14:5e:24:a9:38
  9   9   cu    2G   No_Light 
 10  10   cu    2G   No_Light 
 11  11   cu    2G   No_Light 
 12  12   cu    2G   No_Light 
 13  13   cu    2G   No_Light 
 14  14   cu    2G   No_Light 
 15  15   id    2G   Online    E-Port  20:01:00:0d:ec:06:b4:41 (downstream)
 
 

2.划分zone
Cisco 9120划分zone
  察看fabric连接设备port wwn 信息
switch# show fcns database vsan 1
VSAN 1:
--------------------------------------------------------------------------
FCID        TYPE  PWWN                    (VENDOR)        FC4-TYPE:FEATURE
--------------------------------------------------------------------------
0x630100    N     21:00:00:14:5e:24:a9:04                 scsi-fcp
0x630200    N     21:00:00:14:5e:24:a9:36                 scsi-fcp
0x630300    N     21:00:00:14:5e:24:a9:7a                 scsi-fcp
0x630400    N     21:00:00:14:5e:24:a9:b6                 scsi-fcp
0x630500    N     21:00:00:14:5e:24:a9:28                 scsi-fcp
0x630600    N     21:00:00:14:5e:24:aa:f6                 scsi-fcp
0x630700    N     21:00:00:14:5e:24:aa:f0                 scsi-fcp
0x630800    N     21:00:00:14:5e:24:a9:38                 scsi-fcp
0x640000    N     20:07:00:a0:b8:21:19:9f (SymBios)       scsi-fcp:both
0x640100    N     20:06:00:a0:b8:21:19:9f (SymBios)       scsi-fcp:both

Total number of entries = 10

创建zone
分别创建2个zone，前4个刀片服务器与DS4300 2个控制器组成的zone，第4到第8个刀片服务器与DS4300 2个控制器组成的zone。

switch# config t Enter configuration commands, one per line.  End with CNTL/Z.
switch(config)# zone name blade_hs20_1-4 vsan 1

switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:04

switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:36

switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:7a

switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:b6

switch(config-zone)# member pwwn 20:07:00:a0:b8:21:19:9f

switch(config-zone)# member pwwn 20:06:00:a0:b8:21:19:9f
switch(config-zone)#exit
 switch(config)# zone name blade_hs20_5-8 vsan 1
switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:28

switch(config-zone)# member pwwn 21:00:00:14:5e:24:aa:f6

switch(config-zone)# member pwwn 21:00:00:14:5e:24:aa:f0

switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:38

switch(config-zone)# member pwwn 20:07:00:a0:b8:21:19:9f

switch(config-zone)# member pwwn 20:06:00:a0:b8:21:19:9f
 创建zoneset
switch(config-zone)# zoneset name ds4300_blade vsan 1

switch(config-zoneset)# member Blade_Hs20_1-4
switch(config-zoneset)# member Blade_Hs20_5-8
switch(config-zoneset)# end
激活zoneset switch# config t Enter configuration commands, one per line.  End with CNTL/Z.
switch(config)# zoneset activate name ds4300_blade vsan 1 Zoneset activation initiated. check zone status
 察看激活的zone信息
switch# show zone active vsan 1
zone name blade_hs20_1-4 vsan 1
* fcid 0x630100 [pwwn 21:00:00:14:5e:24:a9:04]
* fcid 0x630200 [pwwn 21:00:00:14:5e:24:a9:36]
* fcid 0x630300 [pwwn 21:00:00:14:5e:24:a9:7a]
* fcid 0x630400 [pwwn 21:00:00:14:5e:24:a9:b6]
* fcid 0x640000 [pwwn 20:07:00:a0:b8:21:19:9f]
* fcid 0x640100 [pwwn 20:06:00:a0:b8:21:19:9f]

zone name blade_hs20_5-8 vsan 1
* fcid 0x630500 [pwwn 21:00:00:14:5e:24:a9:28]
* fcid 0x630600 [pwwn 21:00:00:14:5e:24:aa:f6]
* fcid 0x630700 [pwwn 21:00:00:14:5e:24:aa:f0]
* fcid 0x630800 [pwwn 21:00:00:14:5e:24:a9:38]
* fcid 0x640000 [pwwn 20:07:00:a0:b8:21:19:9f]
* fcid 0x640100 [pwwn 20:06:00:a0:b8:21:19:9f]
 

保存系统配置信息
switch# copy running startup
[########################################] 100%

刀片中心光纤交换机模块查看zone信息

brocadessm:USERID> cfgshow
Defined configuration:
 no configuration defined

Effective configuration:
 cfg: ds4300_blade 
 zone: blade_hs20_1-4 
  21:00:00:14:5e:24:a9:04
  21:00:00:14:5e:24:a9:36
  21:00:00:14:5e:24:a9:7a
  21:00:00:14:5e:24:a9:b6
  20:07:00:a0:b8:21:19:9f
  20:06:00:a0:b8:21:19:9f
 zone: blade_hs20_5-8 
  21:00:00:14:5e:24:a9:28
  21:00:00:14:5e:24:aa:f6
  21:00:00:14:5e:24:aa:f0
  21:00:00:14:5e:24:a9:38
  20:07:00:a0:b8:21:19:9f
  20:06:00:a0:b8:21:19:9f

如上命令输出所示，Cisco 9120的zone 信息已经同步到刀片中心的交换机模块。

系统配置完成。